CABLE HARDWARE

8' long (96") Yellow High density polyethylene guy guard marker. 1.51" OD collapses to 1.375" once installed Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Serving Sleeves, These are usually in a 1x7 configuration: 1 bundle of 7 strands. Cable used in ropes courses and zip lines is usually 7x19 or 6x24: Much more flexible Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Gripple Ropes Course Cable Connector, Learn More

Fist Grip Cable Clamp - Import Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

Crosby Fist Grip Cable Clamps Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Mailion Rapid Links (aka "Rapides" or "Quick-Links") are steel screw-links designed for fastening lengths of chain together on ropes courses and zip lining. They provide critical connections for trolleys, balay devices, cables and cable hardware on a zip line. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

If you plan to wrap the cable around a tree or post and not use bolt a tree wrap is what you need. Learn More

When closed with a wrench, this aluminum quick link is used to close harnesses that have two attachment points that must be joined with a connector. Learn More

When closed with a wrench, this steel quick link becomes a semi-permanent anchor ring. Learn More

When closed with a wrench, this steel quick link becomes a semi-permanent anchor ring. Learn More

Ring helps hold the connector in the correct position. Learn More

These lightweight belay/rappel gloves combine the durability of a work glove with the precise fit and dexterity of a thinner glove. Double-layered leather protects the palm and other high-wear areas. Learn More

Forged Nut Eye bolts are the backbone of ropes challenge course and zip line construction. Zip line and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

The Pear shape offers the same nut opening as large opening quick links but its curved shape allows smooth connection of several parts together. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Yellow 8' Guy Marker - Guy Guard Learn More